In earlier post we gone through the step by step configuration methods of Control or Primary Domain, in this article we are going to discuss about the configuration of Service Domain. As we discussed, earlier Control domain serve as service domain by adding the services. Let we start
List of Topics :
- Basic of LDOM
- Install Prerequisites Packages for LDM.
- Install LDM Agents. (LDM download link)
- Allocate Resource to Control Domain.
- Adding/Deleting Service Domain
- Adding/Deleting Logical Domain.
- Export ISO Image to Logical Domain
- Adding I/O Domain.
- Migrate the Logical Domain to another the Primary Domain.
- LDOM Quick Reference Guide
- Adding Virtual Disk Server.
- Adding Virtual Switch Service.
- Make the Virtual Switch as a Primary interface.
- Adding Virtual Console Concentrator Service.
- Enable the vntsd (Virtual Network Terminal Server Daemon ).
Adding Virtual Disk Server
We have to add virtual disk server, in order to configure the Virtual disk to the logical domain.In the below example, we are creating vdiskserver or vds (primary-vds0) is being added to the control domain (primary)
[root@unixrock /]# ldm add-vdiskserver primary-vds0 primary ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Any configuration changes made will only take effect after the machine configuration is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ [root@unixrock /]#
Adding Virtual Switch Service
vswitch service which enable networking between virtual network device in the domain.In the below example, Virtual switch services (primary-vsw0) connected to the NIC card e1000g0 is being added to the primary domain.
[root@unixrock /]# ldm add-vswitch net-dev=e1000g0 primary-vsw0 primary ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Any configuration changes made will only take effect after the machine configuration is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ [root@unixrock /]#Adding Virtual Console Concentrator
The Virtual Console concentrator service provides the console service to logical domain. we must enable the Virtual Network Terminal Server (vntsd) daemon, In order to provide the service.
[root@unixrock /]# ldm add-vconscon port-range=5000-5100 primary-vconsole primary ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Any configuration changes made will only take effect after the machine configuration is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ [root@unixrock /]#Verifying Virtual Network Terminal Server (vntsd) daemon status
[root@unixrock /]# svcs -a|grep -i vntsd online 8:11:13 svc:/ldoms/vntsd:default [root@unixrock /]#Verifying the services which we have created by executing below commands
[root@unixrock /]# ldm list-services primary
------------------------------------------------------------------------------
Notice: the LDom Manager is running in configuration mode. Configuration and
resource information is displayed for the configuration under construction;
not the current active configuration. The configuration being constructed
will only take effect after it is downloaded to the system controller and
the host is reset.
------------------------------------------------------------------------------
VCC
NAME LDOM PORT-RANGE
primary-vconsole primary 5000-5100
VSW
NAME LDOM MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE
primary-vsw0 primary 00:14:4f:f8:f3:f4 e1000g0 0 switch@0 1 1 1500
VDS
NAME LDOM VOLUME OPTIONS MPGROUP DEVICE
primary-vds0 primary
[root@unixrock /]#
Enabling Networking between the Control/Service Domain and other Domain. Recommend to do it in console, as we are changing the source IP interface configuration, as our Vswitch (vsw0) should be Primary interface.
[root@unixrock /]# dladm show-dev vsw0 link: up speed: 1000 Mbps duplex: full e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 link: unknown speed: 0 Mbps duplex: half e1000g2 link: unknown speed: 0 Mbps duplex: half e1000g3 link: unknown speed: 0 Mbps duplex: half [root@unixrock /]# ifconfig -a lo0: flags=2001000849mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g0: flags=1000843 mtu 1500 index 2 inet 11.0.0.203 netmask ff000000 broadcast 11.255.255.255 ether 0:14:4f:82:5c:ee [root@unixrock /]# [root@unixrock /]# ifconfig e1000g0 down [root@unixrock /]# ifconfig e1000g0 unplumb [root@unixrock /]# ifconfig vsw0 plumb up [root@unixrock /]# mv /etc/hostname.e1000g0 /etc/hostname.vsw0 [root@unixrock /]#
As of now we have configured the Control or Primary Domain as a Service Domain. Still these configuration settings are not yet saved, we must save the configuration in system controller and reboot the OS, in order to take effect the new configuration. Below example, we just deleted the old spconfig file and saved the configuration as config_intial by add-spconfig options.
[root@unixrock /]# ldm list-spconfig factory-default tempprofile [current] [root@unixrock /]# ldm remove-spconfig tempprofile [root@unixrock /]# ldm list-spconfig factory-default [next poweron] [root@unixrock /]# ldm add-spconfig config_intial [root@unixrock /]# ldm list-spconfig factory-default config_intial [current] [root@unixrock /]# [root@unixrock /]#Rebooting the OS, In order to take effect the new configuration
[root@unixrock /]# shutdown -i6 -g0 -y [root@unixrock /]#Perfect !!!!!! Now we have successfully configured the Control or Primary Domain as a Service Domain and we are ready to create the Logical Domain.
No comments:
Post a Comment